[1]Ashizuka M,Kiyohara H,Okuno T,et al.Fatigue behavior of tetragonal zirconia polycrystals (Y-TZP) containing 2 and 4 mol% Y2O3 (part 2). J Ceram Soc Jpn Int.2008;96:731-736.
[2]Derand P,Derand T.Bond strength of luting cements to zirconium oxide ceramics. Int J Prosthodont.2007; 13: 131-135.
[3]Tinschert J,Natt G,Mautsch W,et al.Fracture resistance of lithium dislocate-,alumina-,and zirconia-based three-unit fixed partial dentures: a laboratory study.Int J Prosthodont.2006;14: 231-238.
[4]Burke FJ.Fracture resistance of teeth restored with dentin-bonded crowns: the effect of increased tooth preparation. Quintessence Int.2006;27:115-121.
[5]Atsu SS,Kilicarslan MA,Kucukesmen HC,et al.Effect of zirconium-oxide ceramic surface treatments on the bond strength to adhesive resin.J Proshtet Dent.2006;95:430-436.
[6]Wolfart M,Lehmann F,Wolfart S,et al.Durability of the resin bond strength to zirconia ceramic after using different surface conditioning methods.Dent Mater. 2007;23:45-50.
[7]De Oyagüe RC,Monticelli F,Toledano M,et al.Influence of surface treatments and resin cement selection on bonding to densely-sintered zirconium-oxide ceramic. Dent Mater.2009; 25(2):172-179.
[8]Kern M,Wegner SM.Bonding to zirconia ceramic: adhension methodsand their durability. Dental Mater.2008;14:64-71.
[9]Kern M,Thompson VP. Sandblasting and silica-coating of dental alloys: volume loss, morphology and changes in the surface composition. Dental Mater.2009;9:155-161.
[10]Saka M,Yuzugullu B.Bond strength of veneer ceramic and zirconia cores with different surface modifications after microwave sintering.J Adv Prosthodont.2013;5(4):485-493.
[11]Matinlinna JP, Lassila LVJ, Ozcan M,et al.An introduction to silanes and their clinical applications in dentistry.Int J Prosthodont.2010;17:155-644.
[12]Seabra B,Arantes-Oliveira S,Portugal J.Influence of multimode universal adhesives and zirconia primer application techniques on zirconia repair. J Prosthet Dent. 2014; 112(2):182-187.
[13]Liu D,Pow EH,Tsoi JK,et al.Evaluation of four surface coating treatments for resin to zirconia bonding.J Mech Behav Biomed Mater.2014;32:300-309.
[14]Li R. Development of a ceramic primer with higher bond durability for resin cement. J Oral Rehabil.2010;37(7): 560-568.
[15]Matinlinna JP,Özcan M,Lassila L,et al.Effect of the cross-linking silane concentration in a novel silane system on bonding resin-composite cement. Acta Odont Scand.2008;66: 250-255.
[16]Matinlinna JP,Lassila L,Vallittu P. Pilot evaluation of resin composite cement adhesion to zirconia using a novel silane system. Acta Odont Scand.2007;65:44-51.
[17]Piconi C, Maccauro G. Zirconia as a ceramic material. Biomaterials.1999;20:1-25.
[18]Aboushelib MN, Kleverlaan CJ, Feilzer AJ. Microtensile bond strength of different components of core veneered all-ceramic restorations: Part II: Zirconia veneering ceramics. Dent Mater. 2006;22:857-863.
[19]Menani LR,Farhat IA,Tiossi R,et al.Effect of surface treatment on the bond strength between yttria partially stabilized zirconia ceramics and resin cement. J Prosthet Dent.2014; 112(2): 357-364.
[20]Aboushelib MN,de Jager N,Kleverlaan CJ,et al.Microtensile bond strength of different components of core veneered all-ceramic restorations.Dent Mater. 2005;21:984-991.
[21]Lankford J,Page RA,Rabenberg L.Deformation mechanisms in yttria-stabilized zirconia.J Mater Sci.1988;23:4144-4156.
[22]Deville S,Chevalier J,EI Attaoui H.Atomic force microscopy study and qualitative analysis of martensite relief in zirconia.J Am Ceram Soc.2005;88:1261-1267.
[23]Deville S,Chevalier J,Dauvergne C,et al.Microstructural investigation of the aging behavior of (3y-TZP)-Al2O3 composite.J Am Ceram Soc.2005;88:1273-1280.
[24]Inokoshi M,Kameyama A,De Munck J,et al.Durable bonding to mechanically and/or chemically pre-treated dental zirconia. J Dent.2013;41(2):170-179.
[25]Chen C,Kleverlaan CJ,Feilzer AJ.Effect of an experimental zirconia–silica coating technique on micro tensile bond strength of zirconia in different priming conditions. Dent Mater. 2012;28(8): e127-134.
[26]Kawai N,Lin J,Youmaru H,et al.Effects of three luting agents and cyclic impact loading on shear bond strengths to zirconia with tribochemical treatment. J Dent Sci. 2012;7(2):118-124.
[27]Queiroz JR,Benetti P,Massi M,et al.Effect of multiple firing and silica deposition on the zirconia–porcelain interfacial bond strength.Dent Mater.2012;28(7):763-768.
[28]Piascik JR,Swift EJ,Braswell K,et al.Surface fluorination of zirconia: Adhesive bond strength comparison to commercial primers Dent Mater.2012;6(28):604-608.
[29]Aboushelib M,Feilzer A.New surface treatment for zirconia based materials. European patent application No 050773969; 2006. |