中国组织工程研究

中国组织工程研究 ›› 2012, Vol. 16 ›› Issue (43): 8041-8044.doi: 10.3969/j.issn.2095-4344.2012.43.014

• 组织工程口腔材料 tissue-engineered oral materials • 上一篇    下一篇

氮化钛涂层和黏结瓷对钛瓷结合强度的影响

刘 杰，时 磊，范金杰，葛亚丽，谷晓明   

  1. 佳木斯大学附属口腔医院修复科，黑龙江省佳木斯市 154002
  • 收稿日期:2012-01-21 修回日期:2012-03-12 出版日期:2012-10-21 发布日期:2012-10-21
  • 通讯作者: 刘杰，佳木斯大学附属口腔医院修复科，黑龙江省佳木斯市 154002 graduate2009oral@sina.com
  • 作者简介:刘杰☆，女，1963年生，北京市人，2002年日本长崎大学毕业，博士，副教授，主要从事口腔修复学临床和基础研究。

Effects of titanium nitride coating and bond porcelain on the bonding strength of titanium porcelain

Liu Jie, Shi Lei, Fan Jin-jie, Ge Ya-li, Gu Xiao-ming   

  1. Department of Prosthodontics, Affiliated Stomatological Hospital of Jamusi University, Jamusi 154002, Heilongjiang Province, China
  • Received:2012-01-21 Revised:2012-03-12 Online:2012-10-21 Published:2012-10-21
  • Contact: Liu Jie, Department of Prosthodontics, Affiliated Stomatological Hospital of Jamusi University, Jamusi 154002, Heilongjiang Province, China graduate2009oral@ sina.com
  • About author:Liu Jie☆, Doctor, Associate professor, Department of Prosthodontics, Affiliated Stomatological Hospital of Jamusi University, Jamusi 154002, Heilongjiang Province, China

PDF

361

被引次数

4

摘要：

背景：氮化钛涂层与黏结瓷均可改善钛瓷结合强度。
目的：观察氮化钛涂层和Noritake Ti-22黏结瓷对钛瓷结合强度的影响。
方法：将32个纯钛铸件表面喷砂后分为4组：纯钛组、氮化钛涂层组、黏结瓷涂布组、氮化钛涂层联合黏结瓷涂布组。将处理后各组试件中间部分烤瓷，运用三点弯曲方法测试各组金瓷结合强度。
结果与结论：纯钛组钛瓷结合力低于氮化钛涂层组、黏结瓷涂布组、氮化钛涂层联合黏结瓷涂布组(P < 0.05)，后3组组间结合强度差异无显著性意义(P > 0.05)。氮化钛涂层组、黏结瓷涂布组、氮化钛涂层联合黏结瓷涂布组钛瓷界面结合紧密，无明显孔隙和气泡；纯钛组钛瓷结合界面有明显孔隙。说明氮化钛涂层和黏结瓷的应用有利于提高钛瓷结合强度，单两种处理方法同时作用并不能更好地提高钛瓷结合强度。

关键词: 黏结瓷, 氮化钛涂层, 钛, 瓷, 结合强度, 口腔生物材料, 生物材料

Abstract:

BACKGROUND: Titanium nitride (TiN) coating and bond porcelain can improve the bonding strength of titanium porcelain.
OBJECTIVE: To investigate the influence of TiN and bond porcelain on the bonding strength of titanium porcelain．
METHODS: Totally 32 cast pure Ti plates were prepared. After sandblasting, the cast plates were divided into four groups: A, B, C and D groups. A: pure Ti group, B: TiN coating group, C: bond porcelain coating group, D: TiN+bond porcelain coating group. And then porcelain was baked at the center of the plates. All plates were submitted to a three-point bending test.
RESULTS AND CONCLUSION: The titanium-porcelain binding stength of the group A was lower than that of the groups B, C and D (P < 0.05).There were no significant differences in the bonding strength among the groups B, C and D (P > 0.05). Titanium porcelain interfaces of groups B, C and D were linked closely together, and there were no obvious pores and bubbles. These findings suggest that the application of the TiN and bond porcelain is helpful to improve the bonding strength of titanium porcelain. If they are handled in two ways simultaneously, the bonding strength of titanium porcelain cannot be improved better.

中图分类号: