中国组织工程研究

中国组织工程研究 ›› 2011, Vol. 15 ›› Issue (3): 441-444.doi: 10.3969/j.issn.1673-8225.2011.03.015

• 组织工程口腔材料 tissue-engineered oral materials • 上一篇    下一篇

一种碳/碳复合材料表面制备高结合强度羟基磷灰石涂层的新方法

李冬梅1，熊信柏2，邹春莉2，马楚凡1   

  1. 1解放军第四军医大学口腔医学院修复科，陕西省西安市 710032
    2深圳市特种功能材料重点实验室，广东省深圳市 518060
  • 收稿日期:2010-10-08 修回日期:2010-12-10 出版日期:2011-01-15 发布日期:2011-01-15
  • 通讯作者: 熊信柏，博士，副教授，深圳市特种功能材料重点实验室，广东省深圳市 518060
  • 作者简介:李冬梅☆，女，1974年生，博士，讲师。
  • 基金资助:

    陕西省科技计划项目(2008K14-03)，国家自然科学基金资助(50702034)，深圳市科技计划项目(PT200805200295A)。

A novel method for preparing adherent hydroxyapatite coating on carbon/carbon composite surface

Li Dong-mei1, Xiong Xin-bo2, Zou Chun-li2, Ma Chu-fan1   

  1. 1 Department of Prosthodontics, School of Stomatology, the Fourth Military Medical University of Chinese PLA, Xi’an  710032, Shaanxi Province, China
    2Shenzhen Key Laboratory of Special Functional Materials, Shenzhen  518060, Guangdong Province, China
  • Received:2010-10-08 Revised:2010-12-10 Online:2011-01-15 Published:2011-01-15
  • Contact: Xiong Xin-bo, Doctor, Associate professor, Shenzhen Key Laboratory of Special Functional Materials, Shenzhen 518060, Guangdong Province, China
  • About author:Li Dong-mei☆, Doctor, Lecturer, Department of Prosthodontics, School of Stomatology, the Fourth Military Medical University of Chinese PLA, Xi’an 710032, Shaanxi Province, China
  • Supported by:

    Science and Technology Program of Shaanxi Province, No. 2008K14-03*; the National Natural Science Foundation of China, No. 50702034*; Science and Technology Program of Shenzhen, No. PT200805200295A*

PDF

396

被引次数

1

摘要：

背景：目前在碳/碳表面制备羟基磷灰石涂层的方法有很多种，但所制涂层与基体的结合强度不高。
目的：提出一种在碳/碳复合材料表面制备高结合强度羟基磷灰石涂层的新方法。
方法：首先利用感应加热法在基体表面制备出无水磷酸氢钙涂层，而后对其进行水热处理，转变为羟基磷灰石相。扫描电镜观察涂层的形貌，划痕法测试涂层的临界载荷，顶出法测试剪切强度。
结果与结论：感应热沉积法可以在碳/碳复合材料表面制备出致密的块状晶粒结构的无水磷酸氢钙涂层；通过水热处理可以将其转变成结晶完好致密的羟基磷灰石涂层。涂层的临界载荷为13.31 N，剪切强度约为47 MPa。

关键词: 碳/碳复合材料, 羟基磷灰石, 高频感应加热沉积, 水热反应, 涂层

Abstract:

BACKGROUND: At present, there are many methods for preparing hydroxyapatite (HA) coating on carbon/carbon composite surface, but the bonding strength between the prepared coating and the substrate is not high.
OBJECTIVE: To propose a novel method for preparing HA coating with high bonding strength on carbon/carbon composite surface.
METHODS: Firstly, monetite coating was deposited on carbon/carbon composite using induction heating technique, and then the monetite coating was converted to HA by hydrothermal method in ammonia solution. The morphology of the coating was observed under scanning electron microscopy, the critical load of HA coating was determined using scratch test, and shear strength was detected with extrusion method.
RESULTS AND CONCLUSION: Using induction heat deposition method, dense block anhydrous dicalcium phosphate coating with grain structure was prepared in the carbon/carbon composite surface, and then transformed into dense HA coating with good crystals by hydrothermal method. The critical load of HA coating is 13.31 N and shear strength is 47 MPa.

中图分类号: