中国组织工程研究

中国组织工程研究 ›› 2012, Vol. 16 ›› Issue (26): 4863-4866.doi: 10.3969/j.issn.1673-8225.2012.26.022

• 骨与关节生物力学 bone and joint biomechanics • 上一篇    下一篇

平衡功能障碍康复训练装置的有限元分析

郭星辉，崔海坡，徐秀林   

  1. 上海理工大学医疗器械与食品学院，上海市 200093
  • 收稿日期:2011-12-08 修回日期:2012-04-16 出版日期:2012-06-24 发布日期:2013-11-02
  • 通讯作者: 崔海坡，上海理工大学医疗器械与食品学院，上海市 200093 h_b_cui@163. com
  • 作者简介:郭星辉★，男，1987年生，江西省新余市人，上海理工大学在读硕士，主要从事康复工程及器械方向的研究。 xinghui131421@yahoo.com.cn
  • 基金资助:

    上海市科委科技创新计划资助项目(08440510300)：针对肌肉/平衡功能障碍的智能化评定/训练治疗系统研究

Finite element analysis on rehabilitation training device for balance dysfunction

Guo Xing-hui, Cui Hai-po, Xu Xiu-lin   

  1. School of Medical Equipment and Food, University of Shanghai for Science and Technology, Shanghai 200093, China
  • Received:2011-12-08 Revised:2012-04-16 Online:2012-06-24 Published:2013-11-02
  • Contact: Cui Hai-po, School of Medical Equipment and Food, University of Shanghai for Science and Technology, Shanghai 200093, China h_b_cui@163.com
  • About author:Guo Xing-hui★, Studying for master’s degree, School of Medical Equipment and Food, University of Shanghai for Science and Technology, Shanghai 200093, China xinghui131421@ yahoo.com.cn

PDF

543

被引次数

5

摘要：

背景：为了对平衡功能障碍患者进行有效的康复训练，课题组自行设计了一款康复训练装置。
目的：对自行设计的平衡功能障碍康复训练装置进行强度和刚度分析。
方法：利用有限元分析软件ANSYS的工作界面Workbench对康复训练装置进行了强度和刚度分析。分别模拟临床上平衡功能障碍康复训练时的5种不同工作状况，在相同约束条件下分别施加装置自重载荷和患者体质量载荷，得出在不同工况下的应力分布和变形大小。
结果与结论：5种工况下，应力集中与变形突出的区域大致相同，其数值与角度成正相关关系且最大等效应力值均小于所用材料的屈服强度，说明该康复训练装置的强度满足设计要求，能够承受所加的负载；从最大应力值和变形来看，该装置的设计趋于保守，可通过结构优化减轻整体装置的质量；对于复杂模型，ANSYS最新工作界面Workbench比Classic界面效率更高。

关键词: 平衡功能障碍, 康复训练, 有限元分析, 强度, 刚度

Abstract:

BACKGROUND: A rehabilitation training device has been designed by us for the balance dysfunction.
OBJECTIVE: To analyze the strength and stiffness of the rehabilitation training device.
METHODS: Strength and stiffness analysis was performed using the working interface Workbench of finite element analysis software ANSYS. Five different working conditions were considered. The device's gravity loading and the patient’s weight loading were applied on the finite element model under the same constraints. The stress distribution and deformation were gained for the different working conditions.
RESULTS AND CONCLUSION: Under the five kinds of conditions, the area of stress concentration and maximum deformation was roughly same, and the values were positive correlated with angle. The maximum equivalent stress was less than the yield limit of material, which means that the strength of rehabilitation training device could meet the requirement of design. In the sight of the maximum stress and deformation, the device's design tended to be conservative, and the weight of the whole device could be reduced through the structure optimization. For a complicated model, the new working interface Workbench of ANSYS had higher efficiency than the Classic interface.

中图分类号: